|
Frequency Bands: |
VHF:136–174MHz UHF:400–470MHz UHF:450–520MHz |
|
Channel Capacity: |
1024 |
|
Channel Bandwidth: |
12.5/25kHz |
|
Dimensions: |
125x54x35mm |
|
Weight: |
320g (Standard battery and antenna) |
|
LCD: |
51 mm High Resolution QVGA TFT LCD (240x320 pixels, 262k |
|
Operating Voltage: |
DC 7.3V ±15% |
|
Battery: |
Standard: 2400mAh (Li-Ion) Option: 3400mAh (Li-Ion) |
|
Battery (5-5-90 duty cycle, High TX Power): |
Analogue: 12 Hours Digital: 14 Hours |
|
Model Variant: |
SDP760 without GPS & Man Down SDP760 with GPS & Man Down SDP760 with GPS, Man Down, Full Duplex & Bluetooth |
|
Frequency Stability: |
0.5ppm |
|
|
VHF: High: Up to 5W Low: Up to 1.25W UHF: High: Up to 4.5W Low: Up to 1.25W |
|
Digital Modulation: |
7K60FXD (Data Only) 7K60FXE (Data and Voice) |
|
Analogue Modulation: |
16K 0F3E @ 25kHz 11K 0F3E @ 12.5kHz |
|
Adjacent Channel Power: |
70dB @ 25kHz 60dB @ 12.5 kHz |
|
Conducted and Radiated Emission: |
-36dBm (<1GHz) -30dBm (>1GHz) |
|
Transmission Deviation Limits: |
5kHz @ 25kHz 2.5kHz @ 12.5kHz |
|
Audio Distortion: |
3% Analogue 5% Digital |
|
Hum and Noise: |
49dB @ 25KHz 43dB @ 12.5KHz 55dB @ Digital |
|
Audio Response: |
+1 ~ -3dB |
|
Digital Sensitivity: |
Typical: -121dBm / BER 5% Typical: -118dBm / BER 1% |
|
Analogue Sensitivity: |
Typical: -121dBm / 12dB SINAD |
|
Intermodulation: |
>70dB (TIA603) >65dB (ETSI) |
|
Blocking: |
84dB (TIA603 & ETSI) |
|
Spurious Response Rejection: |
>70dB (TIA603 & ETSI) |
|
Adjacent Channel Selectivity: |
70dB@25 kHz (TIA603 & ETSI) 60dB@12.5 kHz (TIA603 & ETSI) |
|
Conducted Spurious Emission: |
-57dBm (<1GHz) -47dBm (>1GHz) |
|
Rated Audio Power Output: |
1.8W |
|
Rated Audio Distortion: |
3% Analogue 5% Digital |
Hum and Noise: |
49dB @ 25kHz 43dB @ 12.5kHz 55dB @ Digital |
|
Audio Response: |
+1 ~ -3dB |
|
Digital Vocoder Type: |
AMBE+2 |
|
Digital Protocol: |
ETSl TS 102 361-1, -2, -3, -4 |
|
Operating Temperature: |
-30 – +60ºC |
|
Storage Temperature: |
-40 – +85ºC |
|
Dust and Water Intrusion: |
IP67 (IEC60529) |
|
Environmental: |
MIL-STD-810 C/D/E/F/G |
|
ESD: |
IEC 61000-4-2 (level 4) ±8KV (Contact), ±15VK (Air) |
|
Tiff Cold Start: |
<120s |
|
Tiff Hot Start: |
<10s |
|
Horizontal Positioning Accuracy: |
<10s |
|
Acquisition Sensitivity: |
<-140dBm |
|
Tracking Sensitivity: |
<-152dBm |
|
Frequency Bands: |
VHF:136–174MHz UHF:400–470MHz UHF:450–520MHz |
|
Channel Capacity: |
1024 |
|
Channel Bandwidth: |
12.5/25kHz |
|
Dimensions: |
125x54x35mm |
|
Weight: |
320g (Standard battery and antenna) |
|
LCD: |
51 mm High Resolution QVGA TFT LCD (240x320 pixels, 262k |
|
Operating Voltage: |
DC 7.3V ±15% |
|
Battery: |
Standard: 2400mAh (Li-Ion) Option: 3400mAh (Li-Ion) |
|
Battery (5-5-90 duty cycle, High TX Power): |
Analogue: 12 Hours Digital: 14 Hours |
|
Model Variant: |
SDP760 without GPS & Man Down SDP760 with GPS & Man Down SDP760 with GPS, Man Down, Full Duplex & Bluetooth |
|
Frequency Stability: |
0.5ppm |
|
RF Power Output: |
VHF: High: Up to 5W Low: Up to 1.25W UHF: High: Up to 4.5W Low: Up to 1.25W |
|
Digital Modulation: |
7K60FXD (Data Only) 7K60FXE (Data and Voice) |
|
Analogue Modulation: |
16K 0F3E @ 25kHz 11K 0F3E @ 12.5kHz |
|
Adjacent Channel Power: |
70dB @ 25kHz 60dB @ 12.5 kHz |
|
Conducted and Radiated Emission: |
-36dBm (<1GHz) -30dBm (>1GHz) |
| Transmission Deviation Limits: | 5kHz @ 25kHz 2.5kHz @ 12.5kHz |
|
Audio Distortion: |
3% Analogue 5% Digital |
|
Hum and Noise: |
49dB @ 25KHz 43dB @ 12.5KHz 55dB @ Digital |
|
Audio Response: |
+1 ~ -3dB |
|
Digital Sensitivity: |
Typical: -121dBm / BER 5% Typical: -118dBm / BER 1% |
|
Analogue Sensitivity: |
Typical: -121dBm / 12dB SINAD |
|
Intermodulation: |
>70dB (TIA603) >65dB (ETSI) |
|
Blocking: |
84dB (TIA603 & ETSI) |
|
Spurious Response Rejection: |
>70dB (TIA603 & ETSI) |
|
Adjacent Channel Selectivity: |
70dB@25 kHz (TIA603 & ETSI) 60dB@12.5 kHz (TIA603 & ETSI) |
|
Conducted Spurious Emission: |
-57dBm (<1GHz) -47dBm (>1GHz) |
|
Rated Audio Power Output: |
1.8W |
|
Rated Audio Distortion: |
3% Analogue 5% Digital |
|
Hum and Noise: |
49dB @ 25kHz 43dB @ 12.5kHz 55dB @ Digital |
|
Audio Response: |
+1 ~ -3dB |
|
Digital Vocoder Type: |
AMBE+2 |
|
Digital Protocol: |
ETSl TS 102 361-1, -2, -3, -4 |
|
Operating Temperature: |
-30 – +60ºC |
|
Storage Temperature: |
-40 – +85ºC |
|
Dust and Water Intrusion: |
IP67 (IEC60529) |
|
Environmental: |
MIL-STD-810 C/D/E/F/G |
|
ESD: |
IEC 61000-4-2 (level 4) ±8KV (Contact), ±15VK (Air) |
|
Tiff Cold Start: |
<120s |
|
Tiff Hot Start: |
<10s |
|
Horizontal Positioning Accuracy: |
<10s |
|
Acquisition Sensitivity: |
<-140dBm |
|
Tracking Sensitivity: |
<-152dBm |
|
Individual Call |
Radio to radio and radio to/ from dispatch |
|
Group Call |
Radio to group or dispatcher to group |
|
Analogue PABX/ DTMF + Over dial |
DTMF dialling plus onward dial through extensions/ automated reception options |
|
Call to PSTN |
Terminals can call PSTN numbers via the PABX |
|
SIP PABX Call |
Radio to/ from PABX via SIP interface |
|
Short Data Messaging |
Text message to/from radios and/or dispatch |
|
Status Messaging |
Send pre-scanned messages quickly over the air via (short code digits) menu |
|
All Call |
Call to all devices on a network from radio or dispatch with all PTTs disabled |
|
Full Duplex DMO Calls |
Radio to radio calls in full duplex mode |
|
GPS |
Supports Global Positioning System |
| Bluetooth | V4.0, can be used with BT device for audio plus BT PTT Accessory available and BT Palm Microphone for vehicle installs |
|
Noise Reduction |
Software activated in device |
|
Real time clock and Calendar |
Displays date and time in menu bar |
|
French Language |
French GUI |
|
Missed Call List |
Missed calls can be called back from the list via the PTT |
|
Call Diversion |
User can set divert incoming to another radio ID |
|
Dial String Call Modifiers |
Use Dial Strings to modify call types or status messages - includes auto detect telephone dialling |
| Lone Worker | User can set - If idle, radio prompts for response at pre-programmed intervals - radio raises emergency call on pre-configured criteria |
|
Duress Call |
Can be alarm and/or call - configurable hot mic. duration/tone - can use Priority Interrupt |
|
Man Down |
Terminals can be set to trigger a duress call when either tilted beyond a preset amount or no movement detected for a preset time |
|
Emergency Call Indication |
Receiving radio can be set to visually indicate when a call is an Emergency Call |
|
Call Alert |
Radio emits a loud tone until acknowledged by user |
|
Radio Check |
Supplementary feature used by authorised radios to determine whether a particular target radio is switched on with in coverage and active |
|
Radio Monitor |
Supplementary service which enables suitably authorised radios to remotely enable the microphone of target radios for a predefined period of time |
|
Authentication |
Authentication of a device upon registration to a network or on stun/ revive commands |
|
Stun / Revive / Kill |
Stun, revive and/ or kill a radio from an authorised user radio or dispatch |
|
Enable/ Revive |
Similar to stun and revive |
|
Encryption |
AES Encryption 256 bit |
|
OTAP |
Terminals support over the air reprogramming (OTAP) |
|
Enhanced Subscriber Management |
Enhanced management of subscribers configuration and feature control for network operators |
|
Multi Site Roam |
Terminals hunt for strongest signal and can roam between sites |
|
Group Presence Check |
For group calls, only the sites where group members are registered at the time are involved in the call |
|
Mixed Mode Scanning |
Increased network availability and access to mixed digital and analogue channels - Terminals are programmed with scan lists and a scan list can then be assigned to a channel |
|
Operating Modes |
Analogue conventional, digital conventional (DMR Tier II), and digital trunking (DMR Tier III) |
|
Frequency Bands |
Available in VHF and UHF frequency bands |
|
RF performance |
Exceptional RF performance – exceeds ETSI and TIA-603 specifications |
|
Compliance |
Fully compliant with ETSI DMR standards |
|
MIL STD and IP Rating |
MIL-STD-810 & IP67 |
|
Audio Output |
Market leading 1.8W audio output |
|
Receiver sensitivity |
-121dBm receiver sensitivity (typical) – increase coverage area and improve audio quality |
|
Individual Call |
Radio to radio and radio to/ from dispatch. |
|
Group Call |
Radio to group or dispatcher to group. |
|
Analogue PABX/ DTMF + Over dial |
DTMF dialling plus onward dial through extensions/ automated reception options. |
|
Call to PSTN |
Terminals can call PSTN numbers via the PABX. |
|
SIP PABX Call |
Radio to/ from PABX via SIP interface. |
|
Short Data Messaging |
Text message to/from radios and/or dispatch. |
|
Status Messaging |
Send pre-scanned messages quickly over the air via (short code digits) menu. |
|
All Call |
Call to all devices on a network from radio or dispatch with all PTTs disabled. |
|
Full Duplex DMO Calls |
Radio to radio calls in full duplex mode. |
|
GPS |
Supports Global Positioning System. |
|
Bluetooth |
V4.0, can be used with BT device for audio plus BT PTT Accessory available and BT Palm Microphone for vehicle installs. |
|
Noise Reduction |
Software activated in device. |
|
Real time clock and Calendar |
Displays date and time in menu bar. |
|
French Language |
French GUI. |
|
Missed Call List |
Missed calls can be called back from the list via the PTT. |
|
Call Diversion |
User can set divert incoming to another radio ID. |
|
Dial String Call Modifiers |
Use Dial Strings to modify call types or status messages - includes auto detect telephone dialling. |
|
Lone Worker |
User can set - If idle, radio prompts for response at pre-programmed intervals - radio raises emergency call on pre-configured criteria. |
|
Duress Call |
Can be alarm and/or call - configurable hot mic. duration/tone - can use Priority Interrupt. |
|
Man Down |
Terminals can be set to trigger a duress call when either tilted beyond a preset amount or no movement detected for a preset time. |
|
Emergency Call Indication |
Receiving radio can be set to visually indicate when a call is an Emergency Call. |
|
Call Alert |
Radio emits a loud tone until acknowledged by user. |
| Radio Check | Supplementary feature used by authorised radios to determine whether a particular target radio is switched on with in coverage and active. |
| Radio Monitor | Supplementary service which enables suitably authorised radios to remotely enable the microphone of target radios for a predefined period of time. |
|
Authentication |
Authentication of a device upon registration to a network or on stun/ revive commands. |
|
Stun / Revive / Kill |
Stun, revive and/ or kill a radio from an authorised user radio or dispatch. |
|
Enable/ Revive |
Similar to stun and revive. |
|
Encryption |
AES Encryption 256 bit. |
|
OTAP |
Terminals support over the air reprogramming (OTAP) |
|
Enhanced Subscriber Management |
Enhanced management of subscribers configuration and feature control for network operators |
|
Multi Site Roam |
Terminals hunt for strongest signal and can roam between sites |
|
Group Presence Check |
For group calls, only the sites where group members are registered at the time are involved in the call |
|
Mixed Mode Scanning |
Increased network availability and access to mixed digital and analogue channels - Terminals are programmed with scan lists and a scan list can then be assigned to a channel |
|
Operating Modes |
Analogue conventional, digital conventional (DMR Tier II), and digital trunking (DMR Tier III) |
|
Frequency Bands |
Available in VHF and UHF frequency bands |
|
RF performance |
Exceptional RF performance – exceeds ETSI and TIA-603 specifications |
|
Compliance |
Fully compliant with ETSI DMR standards |
|
MIL STD and IP Rating |
MIL-STD-810 & IP67 |
|
Audio Output |
Market leading 1.8W audio output |
|
Receiver sensitivity |
-121dBm receiver sensitivity (typical) – increase coverage area and improve audio quality |
