|
Frequency Bands: |
VHF:136–174MHz UHF:400–470MHz UHF:450–520MHz |
|
Channel Capacity: |
1024 |
|
Channel Bandwidth: |
12.5/25kHz |
|
Dimensions (H x W x D): |
60x174x190mm |
|
Weight: |
1500g |
|
LCD: |
71 mm TFT LCD (320x240 pixels, 262k colors) |
|
Operating Voltage: |
DC 13.6V Nominal DC 10.5-16V Extreme |
|
Current Drain (Transmit): |
8.7A (45W) 7A (25W) 4A (5W) |
|
Model Variant: |
SDM730 25W/45W without GPS SDM730 25W/45W with GPS SDM730 25W/45W with GPS, Full Duplex & Bluetooth (45W model only available in regions where local regulations allow) |
|
Frequency Stability: |
0.5ppm |
|
RF Power Output: |
Selectable levels; 45/25/5 W (45 W model) or 25/5 W (25 W model) |
|
Digital Modulation: |
7K60FXD (Data Only) 7K60FXE (Data and Voice) |
|
Analogue Modulation: |
16K 0F3E @ 25kHz 11K 0F3E @ 12.5kHz |
|
Adjacent Channel Power: |
70dB @ 25kHz 60dB @ 12.5 kHz |
|
Conducted and Radiated Emission: |
-57dBm (<1GHz) -47dBm (>1GHz) |
|
Transmission Deviation Limits: |
5kHz @ 25kHz 2.5kHz @ 12.5kHz |
|
Audio Distortion: |
3% Analogue 5% Digital |
|
Hum and Noise: |
48dB @ 25kHz Analogue 42dB @ 12.5kHz Analogue 55dB @ Digital |
|
Audio Response: |
+1 ~ -3dB |
|
Digital Sensitivity: |
Typical: -121dBm / BER 5% Typical: -118dBm / BER 1% |
|
Analogue Sensitivity: |
Typical: -121dBm / 12dB SINAD |
|
Intermodulation: |
>75dB (TIA603) >70dB (ETSI) |
|
Blocking: |
>95dB (TIA603 & ETSI) |
|
Spurious Response Rejection: |
75dB (TIA603 & ETSI) |
|
Adjacent Channel Selectivity: |
70dB @ 25kHz (TIA603&ETSI) 60dB @ 12.5kHz (TIA603&ETSI) |
|
Conducted Spurious Emission: |
75dB (TIA603 & ETSI) |
|
Rated Audio Power Output: |
5W (Full Duplex) 6.2W (Half-Duplex) |
|
Rated Audio Distortion: |
3% Analogue 5% Digital |
|
Hum and Noise: |
48dB @ 25kHz Analogue 42dB @ 12.5kHz Analogue 55dB @ Digital |
|
Audio Response: |
+1 ~ -3dB |
|
Digital Vocoder Type: |
AMBE+2 |
|
Digital Protocol: |
ETSl-TS102 361 -1, -2,-3,-4 |
|
Operating Temperature: |
-30 – +60ºC |
|
Storage Temperature: |
-40 – +85ºC |
|
Dust and Water Intrusion: |
IP54 |
|
Humidity: |
MIL-STD-810 C/D/E/F/G Standard |
|
ESD: |
IEC 61000-4-2(1evel 4) ±8KV(Contact). ±15KV(Air) |
|
Tiff Cold Start: |
<120s |
|
Tiff Hot Start: |
<10s |
|
Horizontal Positioning Accuracy: |
<10s |
|
Acquisition Sensitivity: |
<-140dBm |
|
Tracking Sensitivity: |
<-152dBm |
|
Frequency Bands: |
VHF:136–174MHz UHF:400–470MHz UHF:450–520MHz |
|
Channel Capacity: |
1024 |
|
Channel Bandwidth: |
12.5/25kHz |
|
Dimensions (H x W x D): |
60x174x190mm |
|
Weight: |
1500g |
|
LCD: |
71 mm TFT LCD (320x240 pixels, 262k colors) |
|
Operating Voltage: |
DC 13.6V Nominal DC 10.5-16V Extreme |
|
Current Drain (Transmit): |
8.7A (45W) 7A (25W) 4A (5W) |
|
Model Variant: |
SDM730 25W/45W without GPS SDM730 25W/45W with GPS SDM730 25W/45W with GPS, Full Duplex & Bluetooth (45W model only available in regions where local regulations allow) |
|
Frequency Stability: |
0.5ppm |
|
RF Power Output: |
Selectable levels; 45/25/5 W (45 W model) or 25/5 W (25 W model) |
|
Digital Modulation: |
7K60FXD (Data Only) 7K60FXE (Data and Voice) |
|
Analogue Modulation: |
16K 0F3E @ 25kHz 11K 0F3E @ 12.5kHz |
|
Adjacent Channel Power: |
70dB @ 25kHz 60dB @ 12.5 kHz |
|
Conducted and Radiated Emission: |
-57dBm (<1GHz) -47dBm (>1GHz) |
|
Transmission Deviation Limits: |
5kHz @ 25kHz 2.5kHz @ 12.5kHz |
|
Audio Distortion: |
3% Analogue 5% Digital |
|
Hum and Noise: |
48dB @ 25kHz Analogue 42dB @ 12.5kHz Analogue 55dB @ Digital |
|
Audio Response: |
+1 ~ -3dB |
|
Digital Sensitivity: |
Typical: -121dBm / BER 5% Typical: -118dBm / BER 1% |
|
Analogue Sensitivity: |
Typical: -121dBm / 12dB SINAD |
|
Intermodulation: |
>75dB (TIA603) >70dB (ETSI) |
|
Blocking: |
>95dB (TIA603 & ETSI) |
|
Spurious Response Rejection: |
75dB (TIA603 & ETSI) |
|
Adjacent Channel Selectivity: |
70dB @ 25kHz (TIA603&ETSI) 60dB @ 12.5kHz (TIA603&ETSI) |
|
Conducted Spurious Emission: |
75dB (TIA603 & ETSI) |
|
Rated Audio Power Output: |
5W (Full Duplex) 6.2W (Half-Duplex) |
|
Rated Audio Distortion: |
3% Analogue 5% Digital |
|
Hum and Noise: |
48dB @ 25kHz Analogue 42dB @ 12.5kHz Analogue 55dB @ Digital |
|
Audio Response: |
+1 ~ -3dB |
|
Digital Vocoder Type: |
AMBE+2 |
|
Digital Protocol: |
ETSl-TS102 361 -1, -2,-3,-4 |
|
Operating Temperature: |
-30 – +60ºC |
|
Storage Temperature: |
-40 – +85ºC |
|
Dust and Water Intrusion: |
IP54 |
|
Humidity: |
MIL-STD-810 C/D/E/F/G Standard |
|
ESD: |
IEC 61000-4-2(1evel 4) ±8KV(Contact). ±15KV(Air) |
|
Tiff Cold Start: |
<120s |
|
Tiff Hot Start: |
<10s |
|
Horizontal Positioning Accuracy: |
<10s |
|
Acquisition Sensitivity: |
<-140dBm |
|
Tracking Sensitivity: |
<-152dBm |
|
Individual Call |
Radio to radio and radio to/ from dispatch |
|
Group Call |
Radio to group or dispatcher to group |
|
Analogue PABX/ DTMF + Over dial |
DTMF dialling plus onward dial through extensions/ automated reception options |
|
Call to PSTN |
Terminals can call PSTN numbers via the PABX |
|
SIP PABX Call |
Radio to/ from PABX via SIP interface |
|
Short Data Messaging |
Text message to/from radios and/or dispatch |
|
Status Messaging |
Send pre-scanned messages quickly over the air via (short code digits) menu |
|
All Call |
Call to all devices on a network from radio or dispatch with all PTTs disabled |
|
Full Duplex DMO Calls |
Radio to radio calls in full duplex mode |
|
GPS |
Supports Global Positioning System |
|
Bluetooth |
V4.0, can be used with BT device for audio plus BT PTT Accessory available and BT Palm Microphone for vehicle installs |
|
Noise Reduction |
Software activated in device |
|
Real time clock and Calendar |
Displays date and time in menu bar |
|
French Language |
French GUI |
|
Missed Call List |
Missed calls can be called back from the list via the PTT |
|
Call Diversion |
User can set divert incoming to another radio ID |
|
Dial String Call Modifiers |
Use Dial Strings to modify call types or status messages - includes auto detect telephone dialling |
|
Lone Worker |
User can set - If idle, radio prompts for response at pre-programmed intervals - radio raises emergency call on pre-configured criteria |
|
Duress Call |
Can be alarm and/or call - configurable hot mic. duration/tone - can use Priority Interrupt |
|
Emergency Call Indication |
Receiving radio can be set to visually indicate when a call is an Emergency Call |
|
Call Alert |
Radio emits a loud tone until acknowledged by user |
|
Radio Check |
Supplementary feature used by authorised radios to determine whether a particular target radio is switched on with in coverage and active |
|
Radio Monitor |
Supplementary service which enables suitably authorised radios to remotely enable the microphone of target radios for a predefined period of time |
|
Authentication |
Authentication of a device upon registration to a network or on stun/ revive commands |
|
Stun / Revive / Kill |
Stun, revive and/ or kill a radio from an authorised user radio or dispatch |
|
Enable/ Revive |
Similar to stun and revive |
|
Encryption |
AES Encryption 256 bit |
|
OTAP |
Terminals support over the air reprogramming (OTAP) |
|
Enhanced Subscriber Management |
Enhanced management of subscribers configuration and feature control for network operators |
|
Multi Site Roam |
Terminals hunt for strongest signal and can roam between sites |
| Group Presence Check | For group calls, only the sites where group members are registered at the time are involved in the call |
| Mixed Mode Scanning | Increased network availability and access to mixed digital and analogue channels - Terminals are programmed with scan lists and a scan list can then be assigned to a channel |
|
Operating Modes |
Analogue conventional, digital conventional (DMR Tier II), and digital trunking (DMR Tier III) |
|
Frequency Bands |
Available in VHF and UHF frequency bands |
|
RF performance |
Exceptional RF performance – exceeds ETSI and TIA-603 specifications |
|
Display |
71mm Transflective TFT LCD display |
|
Compliance |
Fully compliant with ETSI DMR standards |
|
MIL STD and IP Rating |
MIL-STD-810 & IP54 |
|
Audio Output |
Market leading 1.8W audio output |
|
Receiver sensitivity |
-121dBm receiver sensitivity (typical) – increase coverage area and improve audio quality |
|
Individual Call |
Radio to radio and radio to/ from dispatch |
|
Group Call |
Radio to group or dispatcher to group |
|
Analogue PABX/ DTMF + Over dial |
DTMF dialing plus onward dial through extensions/ automated reception options |
|
Call to PSTN |
Terminals can call PSTN numbers via the PABX |
|
SIP PABX Call |
Radio to/ from PABX via SIP interface |
|
Short Data Messaging |
Text message to/from radios and/or dispatch |
|
Status Messaging |
Send pre-scanned messages quickly over the air via (short code digits) menu |
|
All Call |
Call to all devices on a network from radio or dispatch with all PTTs disabled |
|
Full Duplex DMO Calls |
Radio to radio calls in full duplex mode |
|
GPS |
Supports Global Positioning System |
|
Bluetooth |
V4.0, can be used with BT device for audio plus BT PTT Accessory available and BT Palm Microphone for vehicle installs |
|
Noise Reduction |
Software activated in device |
|
Real time clock and Calendar |
Displays date and time in menu bar |
|
French Language |
French GUI |
|
Missed Call List |
Missed calls can be called back from the list via the PTT |
|
Call Diversion |
User can set divert incoming to another radio ID |
|
Dial String Call Modifiers |
Use Dial Strings to modify call types or status messages - includes auto detect telephone dialling |
|
Lone Worker |
User can set - If idle, radio prompts for response at pre-programmed intervals - radio raises emergency call on pre-configured criteria |
|
Duress Call |
Can be alarm and/or call - configurable hot mic. duration/tone - can use Priority Interrupt |
|
Emergency Call Indication |
Receiving radio can be set to visually indicate when a call is an Emergency Call |
|
Call Alert |
Radio emits a loud tone until acknowledged by user |
|
Radio Check |
Supplementary feature used by authorised radios to determine whether a particular target radio is switched on with in coverage and active |
|
Radio Monitor |
Supplementary service which enables suitably authorised radios to remotely enable the microphone of target radios for a predefined period of time |
|
Authentication |
Authentication of a device upon registration to a network or on stun/ revive commands |
|
Stun / Revive / Kill |
Stun, revive and/ or kill a radio from an authorised user radio or dispatch |
|
Enable/ Revive |
Similar to stun and revive |
|
Encryption |
AES Encryption 256 bit |
|
OTAP |
Terminals support over the air reprogramming (OTAP) |
|
Enhanced Subscriber Management |
Enhanced management of subscribers configuration and feature control for network operators |
|
Multi Site Roam |
Terminals hunt for strongest signal and can roam between sites |
|
Group Presence Check |
For group calls, only the sites where group members are registered at the time are involved in the call |
|
Mixed Mode Scanning |
Increased network availability and access to mixed digital and analogue channels - Terminals are programmed with scan lists and a scan list can then be assigned to a channel |
|
Operating Modes |
Analogue conventional, digital conventional (DMR Tier II), and digital trunking (DMR Tier III) |
|
Frequency Bands |
Available in VHF and UHF frequency bands |
|
RF performance |
Exceptional RF performance – exceeds ETSI and TIA-603 specifications |
|
Display |
71mm Transflective TFT LCD display |
|
Compliance |
Fully compliant with ETSI DMR standards |
|
MIL STD and IP Rating |
MIL-STD-810 & IP54 |
|
Audio Output |
Market leading 1.8W audio output |
|
Receiver sensitivity |
-121dBm receiver sensitivity (typical) – increase coverage area and improve audio quality |
